Lessons4 · Turning a stud

The catalogue

Twelve converters, each drawn with a 1-wide tile on every side stud, so you can see whether the tile ends flush, proud or short before you choose.

Each card shows one converter with a tile one stud wide on each of its side studs. Read two things off the drawing. First, whether the top and bottom of the dashed tile meet the dashed lines for the top and bottom of the converter: if they do, the tile is level there. Second, how far the outer face of the tile is from the edge of the stud column. The text under each drawing gives both in numbers.

sourceplatesconverteroutput studtop facebottom face+1+2column
How to read a drawing: the dashed lines are the edges of stud columns, and the orange stud is the one the build exists to produce.
87087

Brick 1×1, stud on 1 side

Brick 1×1, stud on 1 side (3D view)
Stud axis
10 LDU below the top face
Mount face
10 LDU from the column centre
A 1-wide part lands
flush with the top, ½ plate above the bottom; outer face of a plate at 18 LDU
47905

Brick 1×1, studs on 2 opposite sides

Brick 1×1, studs on 2 opposite sides (3D view)
Stud axis
10 LDU below the top face
Mount face
10 LDU from the column centre
A 1-wide part lands
flush with the top, ½ plate above the bottom; outer face of a plate at 18 LDU
3386 / 99206

Plate 1×1×⅔, side stud

Plate 1×1×⅔, side stud (3D view)
Stud axis
6 LDU below the top face
Mount face
10 LDU from the column centre
A 1-wide part lands
½ plate above the top, flush with the bottom; outer face of a plate at 18 LDU
32952 / 22885

Brick 1×1×1⅔, 2 side studs

Brick 1×1×1⅔, 2 side studs (3D view)
Stud axis
30 LDU below the top face
Mount face
10 LDU from the column centre
A 1-wide part lands
2½ plates below the top, flush with the bottom; outer face of a plate at 18 LDU
2nd stud
20 LDU (1 stud) from the first
4070

Headlight brick

Headlight brick (3D view)
Stud axis
10 LDU below the top face
Mount face
6 LDU from the column centre
A 1-wide part lands
flush with the top, ½ plate above the bottom; outer face of a plate at 14 LDU
36841 / 99781

Bracket 1×1 – 1×1, down

Bracket 1×1 – 1×1, down (3D view)
Stud axis
10 LDU below the top face
Mount face
14 LDU from the column centre
A 1-wide part lands
flush with the top, 1½ plates below the bottom; outer face of a plate at 22 LDU
36840 / 99780

Bracket 1×1 – 1×1, up (inverted)

Bracket 1×1 – 1×1, up (inverted) (3D view)
Stud axis
2 LDU above the top face
Mount face
14 LDU from the column centre
A 1-wide part lands
1½ plates above the top, flush with the bottom; outer face of a plate at 22 LDU
79389 / 44728

Bracket 1×1 – 2×1, down

Bracket 1×1 – 2×1, down (3D view)
Stud axis
10 LDU below the top face
Mount face
14 LDU from the column centre
A 1-wide part lands
flush with the top, 1½ plates below the bottom; outer face of a plate at 22 LDU
2nd stud
20 LDU (1 stud) from the first
73825 / 99207

Bracket 1×1 – 2×1, up (inverted)

Bracket 1×1 – 2×1, up (inverted) (3D view)
Stud axis
2 LDU above the top face
Mount face
14 LDU from the column centre
A 1-wide part lands
1½ plates above the top, flush with the bottom; outer face of a plate at 22 LDU
2nd stud
20 LDU (1 stud) from the first
41682

Bracket 2×2 – 1×2, centred

Bracket 2×2 – 1×2, centred (3D view)
Stud axis
10 LDU above the top face
Mount face
4 LDU from the column centre
A 1-wide part lands
2½ plates above the top, 1 plate above the bottom; outer face of a plate at 12 LDU
4081a

Plate 1×1 with ring, thin

Plate 1×1 with ring, thin (3D view)
Stud axis
2 LDU below the top face
Mount face
2 LDU from the column centre
A 1-wide part lands
1 plate above the top, ½ plate below the bottom; outer face of a plate at 10 LDU
4081b

Plate 1×1 with ring, thick

Plate 1×1 with ring, thick (3D view)
Stud axis
2 LDU below the top face
Mount face
4 LDU from the column centre
A 1-wide part lands
1 plate above the top, ½ plate below the bottom; outer face of a plate at 12 LDU

Download CSV