Lessons8 · Studs underneath

The two sums

A chain is a short row of parts that ends in a stud pointing the opposite way. Before you build one, two additions tell you where that last stud will be: one for how far out it sits, one for how high. This page explains what goes into each sum, one number at a time, and then works six chains through.

The chain and its three roles

Every chain on this site has the same three roles. The source is an upright part with a stud on its side. It belongs to the model you already have.

The spacers are ordinary plates pushed onto that side stud, so they stand on edge. A chain has none, one, two or three of them.

The converter is a second part with a side stud, pushed on last, so it lies on its side. Lying down, its own side stud no longer points sideways: it points up or down. That stud is what the chain is for.

A brick with a side stud, two plates on edge and a second brick with a side stud lying on its side, its stud pointing up
Grey, the source. White, two plates on edge. Blue, the converter lying on its side. Orange, the stud the chain produces.

What the two sums measure

Both sums start from the same point: the centre of the source, at the level of its underside.

X is the distance sideways from that point to the centre of the new stud. Z is the height from that point to the surface the new stud stands on.

Both are counted in LDU, the unit in which a stud is 20 wide and a plate is 8 thick. Lesson 2 explains where the unit comes from.

XZ
X is measured along the bottom, Z up the side. Here X is 40 and Z is 24.

First number: the mount face, F

A side stud sticks out of a flat face, and whatever is pushed onto the stud ends up pressed against that face. F is how far that face is from the centre of the part.

On a brick with a side stud the face is the side of the brick itself: 10 LDU from the centre, half a stud.

On a headlight brick the face is sunk 4 LDU into the brick, so F is 6.

On a bracket the stud sits on a thin wall that hangs 4 LDU outside the part, so F is 14.

10614
From the left: a brick with a side stud, a headlight brick and an inverted bracket. The blue bar runs from the centre of each part to the face its side stud stands on.

Second number: the height of the side stud, A

A is how high the centre of the side stud sits above the underside of its own part.

It is 14 on a brick with a side stud and on a headlight brick, and 10 on a plate with a side stud. On a bracket the wall hangs downward, so the stud ends up 2 LDU below the underside: that is written −2.

A height matters for a sideways distance because the converter is lying down. Its underside is pressed against the last plate, so what was its height now runs along the chain: A is how far the new stud sits beyond that plate.

1410−2
From the left: a brick with a side stud, a plate with a side stud and a bracket. The blue bar runs from the underside of each part to the centre of its side stud.

The sum for X

X=Fsource+8n+Aconverter

Read it from left to right along the chain. First from the centre of the source out to its face: F of the source. Then across the plates, 8 for each one; n is how many there are. Then from the last plate to the centre of the new stud: A of the converter.

Studs on a model stand 20 LDU apart. The new stud lines up with them only when X comes to 20, 40 or 60. If it does not, change the number of plates: each one moves the stud by 8.

101614
Two bricks with a side stud and two plates between them: 10 + 16 + 14 = 40, exactly two studs out.

The sum for Z

Z=Asource±Fconverter

The side stud of the source is A above its underside, and the converter hangs on that stud, centred on it. Because the converter is lying down, its mount face has become its top or its bottom. So the new stud stands F above the side stud of the source when it points up, and F below it when it points down: plus for up, minus for down.

1410
14+10=24
Pointing up. 24 LDU is the height of a brick, so the new stud is level with the stud on top of the source.
1410
14−10=4
Pointing down. The same chain turned over leaves the new stud 4 LDU above the underside of the source: half a plate.

Heights on a model go up in plates, 8 LDU at a time, so Z fits when it is a multiple of 8. A Z that is 4 over is half a plate off, the same half plate that lesson 3 is about.

The numbers for each part

These are the values of F and A for the parts used as source or converter. A part with two side studs, one above the other, has two values of A.

The numbers to plug in, LDU
PartMount face, FSide stud above own base, A
Brick 1×1 with Stud on 1 SideBrick 1×1 with Studs on Two Opposite SidesBrick with a side stud, 87087, 479051014
Brick 1×1 with HeadlightHeadlight brick, 4070614
Plate 1×1×0.667 Half Round with Open Side StudPlate 2×2×0.667 with Two Studs On Side and Two RaisedPlate with a side stud, 3386, 992061010
Brick 1×1×1.667 with Studs on 1 SideBrick 1×2×1.667 with Studs on 1 SideTall brick with two side studs, 32952, 228851010 and 30
Bracket 1×1 – 1×1 UpInverted bracket, 368401410
Bracket 1×1 – 1×1 DownBracket, 3684114−2

Download CSV

Six chains worked out

Each sum below is the X sum for the chain drawn above it: F of the source, plus 8 for each plate, plus A of the converter. All six come to a multiple of 20.

3D view: Side-stud brick, 2 plates, Side-stud brick
10+16+14=40
Side-stud brick, 2 plates, side-stud brick: 2 studs out.
3D view: Headlight brick, 0 plates, Headlight brick
6+14=20
Headlight brick, no plates, headlight brick: 1 stud out.
3D view: Headlight brick, 3 plates, ⅔ side-stud plate
6+24+10=40
Headlight brick, 3 plates, ⅔ side-stud plate: 2 studs out.
3D view: Side-stud brick, 0 plates, ⅔ side-stud plate
10+10=20
Side-stud brick, no plates, ⅔ side-stud plate: 1 stud out.
3D view: Inverted bracket, 1 plates, Bracket
14+8−2=20
Inverted bracket, 1 plate, bracket: 1 stud out.
3D view: Inverted bracket, 2 plates, ⅔ side-stud plate
14+16+10=40
Inverted bracket, 2 plates, ⅔ side-stud plate: 2 studs out.