Lessons9 · At an angle

Building a given angle

A part pressed onto a stud sits flat against the part below. It can swivel on a single stud, but it cannot lean, so anything that leans or slopes has to hang between two points that are still on the grid. That one fact decides which angles you can build cleanly. This page explains the rule, lists every angle that works, and finds the nearest one to the angle you want.

The problem with a leaning part

A hinge will stop at any angle you like. The trouble is at the other end. The top of a leaning wall, or the ridge of a roof, has to be held by something, and that something is built from ordinary parts standing on studs.

So a leaning part is never free. It runs from one point on the grid to another point on the grid, and it is a real part with a fixed length. Three lengths have to agree: how far across, how far up, and how long the leaning part is.

34553.1°Built from bricks: a floor with a hinge at its left end, a column of three bricks and two plates at the right with a second hinge on top, and a blue roof five studs long clipped between the two hinges
A leaning part, the floor under it and the upright that holds its top make a right-angled triangle. In bricks: grey, the floor and the two hinges; white, the upright; blue, the leaning part, 3 across, 4 up and 5 long.

The rule

An angle closes up exactly when all three sides of its triangle are whole numbers of studs, measured from pivot to pivot.

The two short sides are on the grid already, so they are whole studs by themselves. The leaning side is the one that usually is not: across 2 and up 2 gives a leaning side of 2.83 studs, and there is no part 2.83 studs long.

Only certain pairs of short sides give a whole number for the third. The smallest is 3 across and 4 up, which gives exactly 5. Double it, 6 and 8, and you get 10.

222.83Built from bricks: eight studs across and eight up. The blue roof, ten studs long, is clipped on at the bottom and points at the top hinge, but its upper clip stops short of the bar
Two across and two up: the leaning side would have to be 2.83 studs long. It cannot be built. The bricks show the same shape four times larger, 8 across and 8 up: a part 10 studs long stops 26 LDU short of the top bar, and one of 12 is too long.

What “pivot to pivot” means

A hinge turns about its bar, not about the edge of its plate. So the length that matters is the distance from the bar at one end of the leaning part to the bar at the other end.

That is easy to count, because the plates made for hinges, with a clip or a handle on the side or on the end, hold their bar exactly one stud, 20 LDU, from the centre of the nearest stud. Count the stud positions from one bar to the other, counting each bar as if it were a stud, and that is the length. A few clips and handles sit elsewhere; Kinds of clip and Kinds of bar give the position of each.

Plate with handle on end 60478 joined to plate with clip on end 63868
A handle on the end of a plate and a clip on the end of another: each bar is one stud beyond the last stud of its plate.

The angles that close exactly

These are all the triangles with whole-stud sides up to 29 studs long. Each one gives two angles, depending on which short side is the floor. Any of them can be doubled or tripled and still works.

1251322.6°Built from bricks: 24 studs across, 10 studs up, a blue roof 26 studs long between two hinges, at 22.6 degrees. The white column is 8 bricks and 2 plates
The second smallest: 12 across, 5 up, 13 along the leaning side. The bricks show it doubled, 24 across, 10 up and 26 along, because a rise of 5 studs is not a whole number of plates.
Exact triangles. Sides in studs.
ViewAngleAcrossUpLeaning side
16.3°24725
22.6°12513
28.1°15817
36.9°435
43.6°212029
46.4°202129
53.1°345
61.9°81517
67.4°51213
73.7°72425

Download CSV

The angles that nearly close

Between the exact angles there are long gaps. A second group fills some of them: triangles whose leaning side misses a whole stud by less than half an LDU, 0.2 mm.

Parts are made about 0.1 mm small on each side so that they slide together, and a clip has a little play on its bar. A miss that small is taken up without visible strain. This site treats half an LDU as the limit; anything larger is left out. Build a close triangle once before you rely on it.

121216.97Built from bricks: 12 studs across, 12 studs up, a blue roof 17 studs long between two hinges, at 45 degrees. The white column is 10 bricks and 1 plate
Twelve across and twelve up, for 45°: the leaning side is 16.97 studs, and a part 17 studs long is 0.6 LDU too long. That is just outside the limit, which is why 45° is the awkward one. Drawn in bricks you cannot see it: 0.6 LDU is a quarter of a millimetre.
Close triangles: the leaning side is within 0.5 LDU of a whole stud. Sides in studs.
ViewAngleAcrossUpLeaning sideMiss, LDU
25.3°199210.48 too short
34.4°1913230.43 too short
34.8°2316280.36 too short
39.0°2117270.37 too short
39.5°1714220.45 too short
50.5°1417220.45 too short
51.0°1721270.37 too short
55.2°1623280.36 too short
55.6°1319230.43 too short
64.7°919210.48 too short

Download CSV

Find the nearest angle

Set the angle you want. The list shows the buildable triangles nearest to it, exact ones first when they tie, and draws the first.

Angle wanted37°

    Going up: studs across, plates up

    A roof or a leaning wall rises in plates, not in studs, so one more thing has to come out even. Five plates are two studs. A rise of 4 studs is 10 plates and a rise of 6 studs is 15 plates, both fine. A rise of 3 studs is seven and a half plates.

    So when the triangle stands upright, the side that goes up has to be an even number of studs, unless you add one half-plate part under the top hinge: a bracket wall or a headlight brick, as in lesson 3. With that part every triangle in the tables can stand up.

    861036.9°Built from bricks: a floor eight studs long from bar to bar, a column of five bricks and a plate, and a blue roof ten studs long clipped onto a hinge at each end
    Eight studs across and six studs up, which is fifteen plates or five bricks. The roof is ten studs long and leans at 36.9°. In the brick version both hinges stand one plate higher, so that the clips clear the floor: the white column is five bricks and a plate.
    Exact triangles standing upright, with the rise in plates. An odd rise needs one half-plate part.
    ViewAngleAcross, studsUp, studsUp, platesRoof, studs
    16.3°24717.5, needs a half-plate part25
    22.6°12512.5, needs a half-plate part13
    22.6°24102526
    28.1°1582017
    36.9°437.5, needs a half-plate part5
    36.9°861510
    43.6°21205029
    46.4°202152.5, needs a half-plate part29
    53.1°34105
    61.9°81537.5, needs a half-plate part17
    67.4°5123013
    73.7°7246025

    Download CSV

    Shallow to steep, in bricks

    Three more triangles from the tables, built the same way and drawn at the same size. In each the rise is an even number of studs, so the white column is whole plates, and the blue roof is a whole number of studs from clip to clip.

    Built from bricks: 15 studs across, 8 studs up, a blue roof 17 studs long between two hinges, at 28.1 degrees. The white column is 7 bricks
    15 across, 8 up, 17 along: 28.1°. The column is seven bricks.
    Built from bricks: 5 studs across, 12 studs up, a blue roof 13 studs long between two hinges, at 67.4 degrees. The white column is 10 bricks and 1 plate
    5 across, 12 up, 13 along: 67.4°. The column is ten bricks and a plate.
    Built from bricks: 7 studs across, 24 studs up, a blue roof 25 studs long between two hinges, at 73.7 degrees. The white column is 20 bricks and 1 plate
    7 across, 24 up, 25 along: 73.7°. The column is twenty bricks and a plate.

    Gentle slopes

    For a shallow slope there is a shortcut. Hinge a long plate at one end and prop the other end up by one or two plates. The plate is slightly too long for its place now, because a tilted plate reaches less far across than a flat one, but for a long plate the difference is tiny.

    One plate of rise is within the half-LDU limit from 4 studs of length upward. Two plates of rise need 13 studs or more.

    A wall that leans only a few degrees from upright can do without the hinge: build it as a slope in steps, in lesson 7.

    60.46Built from bricks: a blue plate six studs long, hinged at the left on a clip and a handle, its right end resting on a tile that stands one plate higher than the hinge end
    A plate six studs long with one end raised by one plate: 3.8°, and only 0.27 LDU shorter across than when it lay flat. In bricks: the blue plate is hinged at the left and rests on a white tile at the right.
    A plate hinged at one end and raised at the other. “Shortfall” is how much less far it reaches than a flat plate.
    ViewLength, studsRaised byAngleShortfall, LDUWithin the limit
    21 plate11.5°0.81no
    31 plate7.7°0.54no
    41 plate5.7°0.40yes
    61 plate3.8°0.27yes
    81 plate2.9°0.20yes
    121 plate1.9°0.13yes
    131 plate1.8°0.12yes
    161 plate1.4°0.10yes
    22 plates23.6°3.34no
    32 plates15.5°2.17no
    42 plates11.5°1.62no
    62 plates7.7°1.07no
    82 plates5.7°0.80no
    122 plates3.8°0.53no
    132 plates3.5°0.49yes
    162 plates2.9°0.40yes

    Download CSV

    Turning in the flat

    A wall that leaves at an angle when seen from above follows the same rule, lying down. Both short sides are counted in studs along the baseplate, so there is no question of plates, and every triangle in the first two tables works as it stands. The pivot can be as simple as one stud: a part held by a single round stud turns on it. The far end drops onto another stud when the triangle is one of the exact ones.

    Seen from above, twice. Left: a grey 4 by 6 plate with two white round 1 by 1 plates on it, four studs across and three along from each other. Right: a blue 1 by 6 plate lying across them at an angle, one end stud on each
    Seen from above. Left, two white round 1 × 1 plates stand 4 studs across and 3 along from each other. Right, a blue 1 × 6 plate dropped onto both: its end studs are exactly 5 apart, so it lies at 36.9°.

    Jumpers halve everything. A jumper puts a stud half way between two others, so the short sides can be counted in half studs: 1½ across and 2 along gives a wall 2½ studs long, the 3, 4, 5 triangle at half size.

    1½22½
    The 3, 4, 5 triangle at half size, with its short sides counted in half studs.

    Angles that are built in

    Some parts carry an angle of their own and need no triangle. Click hinges hold every 22.5°, sixteen steps to a full turn. That gives 22.5°, 45°, 67.5° and 90°, firmly enough to carry weight, and nothing between.

    The nearest exact triangle to 22.5° is 12 across and 5 up, at 22.6°: close enough that a click hinge at one step and that triangle agree.

    Two click hinge plates drawn five times from the side: lying flat, then the blue one raised by 22.5, 45, 67.5 and 90 degrees
    Two click hinge plates (44302 and 44301), seen from the side at every step from flat to upright: 0°, 22.5°, 45°, 67.5° and 90°. The teeth hold each step and nothing between.

    Slope parts are named for their angle. The LDraw library, which this site takes its parts from, gives these.

    A small 1 × 2 slope
    The small 1 × 2 slope (85984), a 31° part.
    Slope parts and the angle in their name
    ViewPartNumberAngle
    Small slope 1 × 1, 54200Small slope 1 × 15420031°
    Small slope 1 × 2, 85984Small slope 1 × 28598431°
    Slope 4 × 1, 60477Slope 4 × 16047718°
    Slope 3 × 1, 4286Slope 3 × 1428633°
    Slope 2 × 1, 3040Slope 2 × 1304045°
    Tall slope 2 × 1 × 2, 60481Tall slope 2 × 1 × 26048165°
    Tall slope 2 × 1 × 3, 4460Tall slope 2 × 1 × 3446075°

    Download CSV

    A build to try

    You need two plates with a handle on the end, two plates with a clip on the end, and ordinary plates and bricks.

    Lay a floor 8 studs long from bar to bar. At one end build straight up 6 studs, which is 5 bricks. Make a roof 10 studs long from bar to bar and clip it on at both ends. It goes on without bending, at 36.9°. Now try 7 up instead of 6: it will not close.

    861036.9°
    The same triangle as above: 8 across, 6 up, 10 along the roof.